icnd2 200-105 Exam Dumps Questions

Various complicated topics related of Routing and Switching, LAN switching technologies, IPv4 and IPv6 routing technologies are included in this 200-105 exam.

Try it Latest DumpsSchool 200-105 Exam dumps. Buy Full File here: https://www.dumpsschool.com/200-105-exam-dumps.html (691 As Dumps)

Download the DumpsSchool 200-105 braindumps from Google Drive: https://drive.google.com/file/d/1TwCxP9R2WPXn5O77CUBND73niqczpZDp/view (FREE VERSION!!!)

Question No. 1

Given an IP address 172.16.28.252 with a subnet mask of 255.255.240.0, what is the correct network

address?

Answer: A

Question No. 2

What is the default VLAN on an access port?

Answer: B

Question No. 3

Refer to the exhibit.

Router edge-1 is unable to establish OSPF neighbor adjacency with router ISP-1. Which two configuration changes can you make on edge-1 to allow the two routers to establish adjacency? (Choose two.)

Answer: D, E

A situation can occur where the interface MTU is at a high value, for example 9000, while the real value of the size of packets that can be forwarded over this interface is 1500.

If there is a mismatch on MTU on both sides of the link where OSPF runs, then the OSPF adjacency will not form because the MTU value is carried in the Database Description (DBD) packets and checked on the other side.

Question No. 4

Which switch port mode prevents DTP frames from being sent?

Answer: D

Question No. 5

What is one benefit of PVST+?

Answer: C

Per VLAN Spanning Tree (PVST)

Introduction

http://www.cisco.com/en/US/tech/tk389/tk621/tk846/tsd_technology_support_sub-protocol_home.html

Per VLAN Spanning Tree (PVST) maintains a spanning tree instance for each VLAN configured in the network. This means a switch can be the root bridge of a VLAN while another switch can be the root bridge of other VLANs in a common topology. For example, Switch 1 can be the root bridge for Voice data while Switch 2 can be the root bridge for Video data. If designed correctly, it can optimize the network traffic.

http://www.ciscopress.com/articles/article.asp?p=102157&seqNum=4

Question No. 6

Refer to the exhibit.

While troubleshooting a switch, you executed the show interface port-channel 1 etherchannel command and it returned this output. Which information is provided by the Load value?

Answer: D

Question No. 7

Which protocol is an open standard protocol framework that is commonly used in VPNs, to provide secure end-to-end communications?

Answer: C

Internet Protocol Security (IPsec) is a technology protocol suite for securing Internet Protocol (IP) communications by authenticating and/or encrypting each IP packet of a communication session. IPsec also includes protocols for establishing mutual authentication between agents at the beginning of the session and negotiation of cryptographic keys to be used during the session.

Question No. 8

What is the minimum command to turn on encryption on SNMP?

Answer: A

Question No. 9

You attempt to execute the APIC-EM ACL path trace feature without specifying the protocol. How does the

ACL path trace respond?

Answer: A

Question No. 10

Which two statements about the Cisco APIC-EM ACL Path Trace feature are true? (Choose two.)

Answer: A, C

https://www.cisco.com/c/en/us/td/docs/cloud-systems-management/application-policyinfrastructure-

controller-enterprise-module/1-2-x/config-guide/b_apic-em_config_guide_v_1-2-x/b_apicem_

config_guide_v_1-2-x_chapter_01000.pdf

Question No. 11

Which routing protocol is most appropriate for sending and receiving routes directly to and from the Internet?

Answer: B

Question No. 12

What command is used to verify the DLCI destination address in a Frame Relay static configuration?

Answer: C

Cisco Frame Relay Configurations

http://www.ciscopress.com/articles/article.asp?p=170741&seqNum=9

show frame-relay map

The show frame-relay map privileged EXEC mode command shows the contents of the next hop protocol address to DLCI mapping table on the router. The table contains both dynamic mapped and static mapped entries. The below example shows a sample output of the show frame-relay map command.

Router#show frame-relay map

Serial1/2 (up): ip 172.16.1.4 dlci 401(0x191,0x6410), dynamic,

broadcast,, status defined, active

Serial1/2 (up): ip 172.16.1.5 dlci 501(0x1F5,0x7C50), dynamic,

broadcast,, status defined, active

Serial1/2 (up): ip 172.16.1.2 dlci 301(0x12D,0x48D0), dynamic,

broadcast,, status defined, active

Question No. 13

Which command do you enter to create an SVI?

Answer: A

Question No. 14

Refer to the exhibit. The user at Workstation B reports that Server A cannot be reached.

What is preventing Workstation B from reaching Server A?

Answer: D

200-105 Dumps Google Drive: (Limited Version!!!)
https://drive.google.com/file/d/1TwCxP9R2WPXn5O77CUBND73niqczpZDp/view

Related Certification: CCNA Routing & Switching dumps

Leave a Reply

Your email address will not be published. Required fields are marked *